Direct and simultaneous voltammetric analysis of heavy metals in tap water samples at Assiut city: an approach to improve the analysis time for nickel and cobalt determination at mercury film electrode

Tap water samples (Assiut city, lie in the middle north of upper Egypt, approx. 370 km from Cairo, January-March, 2002) were taken from the eight sampling sites of different locations at Assiut city. The samples are analyzed to determine the total content of cadmium, copper, lead and zinc by differential pulse anodic stripping voltammetry (DPASV) while nickel and cobalt are determined by a new simple differential pulse adsorptive stripping voltammetry (DPAdSV), using dimethylglyoxime (DMG) as the complexing agent. This method uses sodium sulfite as the supporting electrolyte, which facilitates the removal of oxygen interference without the traditional necessity of purging with inert gas. The effect of various parameters was studied using DPASV (for Cd, Pb, Cu and Zn) and AdSV (for Ni and Co) methods. Subsequently, under the so found experimental conditions, the stability of calibration curves and the detection limits (μg/l) have been determined. The data achieved (for all metals utility) are comparable to those measured by the graphite furnace atomic absorption spectrophotometric (GF-AAS) method. The effects of the interferences between these metal ions have been investigated. Moreover, the effect of storage was discussed and the obtained results were compared favorably with standard official methods. Statistical analysis of the database exhibits applicability and the accuracy of the techniques. The results obtained from the two techniques (Voltammetry and GF-AAS) are in very good agreements in the most tap water samples.     

Determination of linuron in soil by stripping voltammetry with a carbon fiber microelectrode

A carbon fiber microelectrode was used for the electroanalytical determination of Linuron (LIN) in soil extracts. The microelectrode was subjected to an electrochemical pretreatment in order to improve the herbicide adsorption on the electrode surface. With this preconcentration step, detection limits of 80 ng ml⁻¹ and determination limits of 260 ng ml⁻¹ were reached. Optimal conditions with respect to accumulation time and potential, scan rate and pH were established. The LIN was determined in a soil sample with the method proposed and the results found were comparable to those obtained by HPLC.     

Thermal behavior of glutamic acid and its sodium,lithium and ammonium salts

Glutamic acid (H2_glu) and its lithium, sodium and ammonium monosalts were submitted to thermal analysis using thermogravimetry (TG) and differential thermal analysis (DTA). The main goal of these studies was to compare the relative thermal stability and to evaluate the effect of the counter ion in the thermal decomposition pathways. Salts were obtained by direct neutralization of the purified acid with LiOH, NaOH or NH₄OH and were characterized by elemental analysis (C, H and N) and IR spectroscopy. Decomposition occurred after conversion to the pyroglutamic acid or the respective pyroglutamates and ammonium salt loosing NH₃ being converted to H₂glu before decomposition.     

Fractionation and Bioaccessibility of Manganese,Copper, Zinc,Cadmium, and Lead in Commercial Vegetable and Rice Baby Foods Using Inductively Coupled Plasma - Mass Spectrometry (ICP-MS) with Central Composite Design (CCD)

Abstract

Herein the bioaccessibility of Mn, Cu, Zn, Cd, and Pb, selected from essential and toxic elements, was determined in commercially sold vegetable purees intended for infant and toddler consumption. Chemical fractionation studies using water, acetone, diethyl ether, chloroform:methanol, and n-hexane were employed to predict the importance of the protein and lipid parts of a matrix to assess the bioaccessibility data. In addition, in-vitro gastrointestinal digestion was performed to determine the bioaccessibility of the elements using a five level, three factor central composite design (CCD) to maximize the elemental solubility. The total elemental concentrations in all of the fractions were determined by inductively coupled plasma – mass spectrometry (ICP-MS). Based on the consumption of one jar of vegetable/rice-based baby food, Zn was 1.3% of the recommended dietary allowance and Mn was 4.2% of the adequate intake level, while Cu was almost 100% of the adequate intake level. Additionally, Pb was always below the detection limit and Cd was sometimes under the detection limit for the percent bioaccessibility. However, in some samples, Cd was as high as 80% of the tolerable weekly intake level depending on the body weight.     

密封罐微波消化法序列ICP-AES测定环境试样中多元素

本文采用密闭罐微波消化方法快速分解生物、土壤、沉积物等环境样品。按样品性质,分别采用HNO3/H_2O_2或HNO_3/H_2O_2/HF在聚四氟乙稀密闭罐中于500W微波功率分解0.1～0.2g样品2～3min,溶液(或在其中加入10ml硼酸饱和溶液)稀释至2.5～5.0ml后,直接用序列ICP-AES法测定。方法准确度经分析6个生物、土壤、沉积物标准参考物质验证,10个元素的均值均与定值吻合。     

超高效合相色谱法快速检测塑料食品接触材料中13种紫外吸收剂

建立了一种同时检测塑料食品接触材料中13种紫外吸收剂的超高效合相色谱法。以甲醇为溶剂对塑料食品接触材料样品进行超声提取，经C18固相萃取柱净化，过0.22 μm有机滤膜，采用超高效合相色谱仪分析。选择ACQUTY UPC² HSS C18 SB色谱柱（150 mm×3.0 mm，1.8 μm），以超临界二氧化碳为流动相，异丙醇为改性剂进行梯度洗脱，在最优色谱条件下，13种紫外吸收剂能够在4 min内实现有效分离。结果表明，在各自线性范围内，13种紫外吸收剂的线性关系良好，标准曲线相关系数不低于0.9985，检出限（S/N=3）为0.05~0.15 mg/kg，加标回收率为86.8%~115.7%，相对标准偏差为0.73%~5.61%。该方法快速简便，准确可靠，同时大大减少了有机溶剂的消耗，可用于塑料食品接触材料中13种紫外吸收剂的快速检测。     

水中酚类化合物的液-液-液微萃取/ 高效液相色谱联用分析研究

建立了液-液-液微萃取/高效液相色谱联用(LLLME/HPLC)测定环境水中痕量酚类化合物2-甲基苯酚、2-硝基苯酚、2,4-二氯苯酚的分析方法,研究了有机相溶剂种类及其体积、料液相pH值与离子强度、接受相的体积、组成及浓度和搅拌速率、萃取时间等因素对分析物萃取效率的影响。实验结果表明,该方法对酚类化合物的富集倍数可达到404~747倍,方法的线性范围为0.2~300μg/L,RSD(n=6)为6.8%~11.4%。测定加标自来水、江水以及生活污水样品的回收率为83%~110%。     

Simultaneous sample preparation for high-performance liquid chromatographic determination of Vitamin A and β-carotene in emulsified nutritional supplements after solid-phase extraction

Determination of small amounts of the fat-soluble species Vitamin A (VA) (2.5 μg/g) and β-carotene (9 μg/g) from emulsified nutritional supplements containing 50 kinds of co-existing compounds and a fat content between 2000 and 8000 times higher was performed by solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) with fluorescence detection set at ex. 350 nm and em. 480 nm, and visible detection at 450 nm using an Inertsil ODS 80A (5 μm) analytical column. Mobile phases of methanol-ethanol (50:50) and acetonitrile-ethanol (70:30) were used for the both vitamins. A Bond Elut C₁₈ cartridge was chosen for SPE after comparison with eight other types of SPE cartridge. Retention time of VA and β-carotene was 7 and 8 min, respectively, giving a limit of detection of ca. 0.1 ng per injection at a signal-to-noise ratio 3:1. Recoveries of VA and β-carotene were over 90% by the standard addition method. Relative standard deviation of VA and β-carotene were ca. 2.9 (n=5) and 2.3% (n=5), respectively.     

Molar mass distributions by gradient liquid chromatography: predicting and tailoring selectivity

Interactive liquid chromatography (iLC) for polymer analysis is usually applied to the characterisation of distributions other than molar mass. In particular, its use for the determination of chemical-composition, functionality-type and tacticity distributions has been demonstrated. The application of iLC for the determination of molar mass distributions (MMDs), however, has not yet been fully explored. An expanded version of the reversed-phase liquid chromatography model has been developed to describe and predict how the retention behaviour of polydisperse polystyrene samples changes with molar mass. The relationship between molar mass and the parameters of the model has been investigated in some detail and non-linear correlations were found. From the model and the relationships between the model parameters and molar mass, calibration curves (retention time versus molar mass) were constructed to predict changes in chromatographic selectivity across a given molar mass range. These calibration curves were compared to experimentally obtained curves and, in most cases, excellent agreement was found. The dramatic enhancement in selectivity that can be obtained with iLC in comparison to size-exclusion chromatography (SEC) was illustrated by measuring matrix-assisted laser desorption ionisation (MALDI) MS spectra of fractions collected during a gradient-LC separation. In the low-molar mass range, essentially monodisperse fractions were obtained. Calibration curves, predicted by the model and validated experimentally using narrow-dispersity standards and MALDI-MS spectra of fractions, were used to determine the molar mass distribution of some narrowly distributed polystyrene samples. Molar mass distributions for such standards were found to be somewhat lower than the values reported by the manufacturers. The results also deviated from those obtained by MALDI-MS.     

Nutritional parameters of commercially available milk samples by FTIR and chemometric techniques

A chemometric study on the prediction of the main nutritional aspects of milk has been carried out by using fourier transform infrared spectroscopy (FTIR) attenuated total reflectance (ATR) measurements of commercially available milk samples of different types. Whole, semi and skimmed milks, enriched or not with calcium, vitamins or modified by alteration of lipid or sugar composition were considered. After evaluating different strategies for data acquisition and ATR cleaning between samples, hierarchical cluster analysis (HCA) was carried out for classification of samples in order to choose the calibration set. The prediction capabilities of partial least squares (PLS) data treatment were evaluated in order to obtain information about total fat, total protein, total carbohydrates (CH), calories and calcium. On using the mean square error of cross-validation and prediction as control variables, a critical evaluation were made about the calibration set to be used, the spectral range to be considered and the data treatment (PLS-1 or PLS-2) to be performed. By selecting a calibration set of 33 samples the properties of 48 samples were predicted with relative precision of triplicates of 0.062, 0.040 and 0.039% w/v for total fat, protein and carbohydrates, and 0.66 kcal/100 ml for calories, and 2.1 mg of Ca/100 ml. The mean difference (d_x−y) between predicted and actual values and standard deviation of mean differences (s_x−y), were of 0.06 (0.38), 0.03 (0.18) and −0.15 (0.41), being s_x−y values between brackets, for total fat, proteins and carbohydrates, 0.06 (3.8) kcal/100 ml for calories and −4.5 (9) mg/100 ml for calcium.The sensitivity and selectivity of the methodology developed were evaluated on terms of the net analyte signal. Selectivity factors ranging from 2 to 7.6% have been calculated for the five parameters considered.